Advertising:
T3Technique

Difference between revisions of "Misc"

From Vanagon Diesel Information
Jump to navigation Jump to search
Line 84: Line 84:
  
 
[[File:Vanagon tacho backplate.jpg]]
 
[[File:Vanagon tacho backplate.jpg]]
 +
 +
Remove the MK2 unit from it's backplate
 +
 +
[[File:MK2 tacho unit removed.jpg]]
  
 
== Engine Block Heater ==
 
== Engine Block Heater ==

Revision as of 03:00, 23 September 2016

This is for optional upgrades to the engine which are not exactly required.

Diesel Cluster w/ tachometer

IN PROGRESS

NOTE: This has assumed you've upgraded your alternator to one with a W terminal (usually a 90a)

Shout out to Jason Newton @ Peace Vans for the help!

Reference

TheSamba - Diesel Tach availability problem - Solved

What you want

Vanagon Diesel Tacho Cluster.jpg

What you start with

Vanagon Diesel CF.jpg

Okay, the easiest way to do this is to obtain a MK2 CE1 cluster like the one below:

VW MK2 CE1 DASH CLUSTER.jpg

It has a diesel calibrated tachometer already. It should be a plug and chug and go! Well, that's AFTER you connect the wire to the W termina off your alternator.

In addition, you'll need a later 86-90 dash cluster, I got an 87 that was in good condition.

The key then is to swap the diesel components over into the gasser cluster. Those two things are

  • Glow Plug LED ; The OXS isn't yellow, so this LED will need to be swapped over.
  • Glow Plug LED Indicator sign; So it doesn't say OXS
  • Diesel Tachometer; swapping the gasser for this one

Disassembling Clusters

Most of the cluster is pretty self explainatory with what screws and nuts to remove. It also indicates on the ribbon well where to pull up and where you can't, so I won't cover much on that.

Use a salad fork for areas to lift off of prongs and what not. It'll make it easier to work with.

Some key points to remember though are:

  • Remove ALL cluster lights BEFORE removing any of the ribbon cable; the twist and pull lights
  • LED's have polarity so remember how you removed them and put them into the other cluster.

GP Indicator Swap

So, when you move the backing and the ribbon cable has some flex you'll see this box with one screw towards you. Away from you will be two progs the box locks into place. Remvoe the screw as indicated in the below photo.

Vanagon Diesel CF-b.jpg

In the photo below you see the other side which has two nubs which if you spread out will let that assembly pop out

Vanagon Diesel CF-c.jpg

The box removed

Vanagon Diesel CF-d.jpg

Now, I'll save you the experience I had! The boxes for the Diesel & Gasser is different as seen below:

Vanagon Diesel CF-e.jpg

Now, you'll need to modify the diesel box. You need to break off the tabs going around the grey/white center box. In the below photo I show you what the tabs are to break. I have some broken already (as you should do) and a few unbroken ones on the left.

Vanagon Diesel CF-f.jpg

When you swap the diesel one over, and set the LED's and the back-plate back on, you'll have this:

Vanagon Diesel CF-g.jpg

Assemble Diesel Tachometer

The main issue with the MK2 tachometer is the white backplate is NOT wide enough for the Vanagon cluster box as seen below

MK2 tacho in vanagon test fit.jpg

As you can see it won't work. What you need is the Vanagon tachometer backplate to retro fit on it as such:

Vanagon tacho backplate.jpg

Remove the MK2 unit from it's backplate

MK2 tacho unit removed.jpg

Engine Block Heater

I installed a Zerostart 3100034 Block Heater for a 36.5mm freeze plug which will fit all the VW Inline 4s

VW-inline4-zerostart block heater-a.jpg

Tools

8mm socket / screw driver

Remove Freeze Plug

Remove the second (middle of the three) freeze plugs.

AHU zerostart blockheater freezeplug removal.jpg

Install Zerostart

Use coolant on your finger to go around the Zerostart o-ring and on the engine block mounting part of the freeze-plug hole.

Then push in the Zerostart into the freeze plug hole at a 6 O' Clock orientation till it won't go in any-longer.

VW-inline4-zerostart block heater-install-orientation.jpg

When pressed in tighten the 8mm nut @ 25foot/inches, or by hand till it gets tightened. I did mine by hand.

End result:

VW-inline4-zerostart block heater-installed.jpg